2016 Ram 2500

What owners should know

Covers 2013–2018 · 6.7L Cummins diesel, 6.4L and 5.7L Hemi V8 gas · Updated 2026-10-01

Researched from owner forums and NHTSA complaints and written by Know Your Truck. These are patterns in what owners report, not a guarantee about any particular truck.

Common failures & how to fix them

Parts and video buttons search for your 2016 Ram 2500. Always confirm a part fits using your VIN. Brakes, steering, fuel and airbag work affects your safety, so if you're not sure, have a qualified mechanic do it.

• ABS and stability control failure (2017–2018)

  Dealer (recall)

  Signs: ABS, traction control or 'service electronic brake system' warning lights.

  Fix: Covered by a Chrysler recall for the ABS hydraulic control unit.

  May be covered free by recall 24V896000. Check the VIN at nhtsa.gov/recalls.

• 6.7L Cummins DEF heater failure

  Moderate DIY

  Signs: DEF warning, reduced power, especially in cold weather.

  Fix: Replace the DEF heater or tank assembly. Use fresh DEF and keep the cap closed.

  Shop: 6.7 Cummins DEF heater▶ How-to videos

• 6.7L Cummins EGR cooler leak

  Best left to a shop

  Signs: Coolant loss, white smoke or steam from the exhaust.

  Fix: Replace the EGR cooler.

  Shop: 6.7 Cummins EGR cooler▶ How-to videos

• Drag link can separate

  Dealer (recall)

  Signs: Loose steering or a clunk. In rare cases the drag link can come apart.

  Fix: Covered by a Chrysler recall (a jam nut can loosen).

  May be covered free by recall 19V021000. Check the VIN at nhtsa.gov/recalls.

• 6.4L Hemi ticking

  Best left to a shop

  Signs: A ticking noise, sometimes with a misfire.

  Fix: Have a shop find the cause. It can be broken exhaust manifold bolts (cheaper) or a worn lifter and camshaft (expensive).

  ▶ How-to videos

Recalls

A recall doesn't mean a truck still has the problem. Enter the truck's VIN at nhtsa.gov/recalls or ask a dealer to see whether the repair was done.

• Air Bags:Side/Window:Curtain:Inflator

  Jan 2025 · #25V010000

  Chrysler (FCA US, LLC) is recalling certain 2016-2019 Ram 3500, Ram 1500, 2016-2020 Ram 2500, and 2016 Ram 3500 Cab Chassis vehicles. The right and left side curtain air bag inflators may rupture due to a manufacturing defect.

  Risk and fix

  Risk: An inflator rupture may result in sharp metal fragments striking occupants, resulting in injury.

  Fix: Dealers will replace one or both side curtain air bags, as necessary, free of charge. Owner notification letters were mailed February 13, 2025. Owners may contact FCA customer service at 1-800-853-1403. FCA's numbers for this recall are 05C, 09C, and 10C.

• Air Bags:Side/Window:Curtain:Inflator

  Aug 2021 · #21V632000

  Chrysler (FCA US, LLC) is recalling certain 2015-2020 Ram 1500 Classic, 2015-2016 Ram 3500, and Ram 2500 vehicles, and 2016 Ram 3500 Cab Chassis with a gross vehicle weight rating less than 10,000 lbs. The side air bag inflatable curtain (SABIC) inflator end cap may detach from the inflator, or the inflator sidewall may rupture.

  Risk and fix

  Risk: A separated inflator end cap or inflator rupture can allow compressed gas to escape, resulting in the end cap or other components being propelled into the vehicle, increasing the risk of injury or crash.

  Fix: Dealers will inspect and replace as necessary, the SABIC assemblies, free of charge. Interim owner notification letters were mailed on October 4, 2021. Owner notification letters were mailed on May 26, 2022. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is Y55.

• Latches/Locks/Linkages:Tailgate:Latch

  May 2019 · #19V347000

  Chrysler (FCA US LLC) is recalling certain 2015-2017 Ram 1500, 2500 and 3500 pickup trucks equipped with an 8 foot bed and a power locking tailgate. Chrysler is also recalling all 2013-2014 and 2018 Ram 1500, 2500 and 3500 pickup trucks built before April 1, 2018 with a 6 or 8 foot bed and a power locking tailgate. On August 29, 2019 Chrysler expanded the recall to include an additional 693,128 model year 2013-2014 Ram 1500, 2500 and 3500 pickup trucks. The tailgate actuator limiter tab may fracture and cause the tailgate to unlatch and open while driving.

  Risk and fix

  Risk: If the tailgate opens while the vehicle is being driven, cargo may fall out the vehicle and create a road hazard, increasing the risk of crash.

  Fix: Chrysler will notify owners, and dealers will repair the tailgate latch, free of charge. The recall began May 23, 2019. Chrysler is expected to notify owners of the expanded population on October 18, 2019. Owners may contact FCA US customer service at 1-800-853-1403. FCA US's number for this recall is V44. Note: 2015-2017 MY Ram 1500 pickup trucks with truck beds other than 8 foot, are currently covered under NHTSA recall 18V-486 for this issue.

• Steering:Linkages:Drag:Link:Connection

  Jan 2019 · #19V021000

  Chrysler (FCA US LLC) is recalling certain 2013-2018 Ram 3500 and 2014-2018 Ram 3500 Chassis Cab and Ram 2500 vehicles. The outboard steering linkage jam nut may loosen, allowing one end of the drag link to separate.

  Risk and fix

  Risk: A drag link separation can cause a loss of steering control, increasing the risk of crash.

  Fix: Chrysler will notify owners, and dealers will check the steering linkage jam nut tightness, replacing the drag link assembly or welding the nut to the adjuster sleeve, free of charge. The recall began March 22, 2019. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is V06.

• Steering:Linkages

  Oct 2018 · #18E096000

  Streetcar ORV LLC (Streetcar) is recalling certain American Expedition Vehicles (AEV) 3" Dualsport aftermarket suspension kits, part numbers N0436000 and N0436001, sold for installation on 2013-2018 RAM 2500 and 3500HD trucks. Improper installation and machining of the original equipment steering knuckle may weaken the joint between the steering drag link and knuckle.

  Risk and fix

  Risk: The weakened connection may result in a fractured steering drag link, causing a loss of steering and increasing the risk of a crash.

  Fix: Streetcar will notify owners and dealers will inspect and install a new steering knuckle, free of charge. The recall began December 3, 2018. Owners may contact AEV customer service at 1-248-926-0256, extension 500.

• Structure:Body:Tailgate

  Jul 2018 · #18V486000

  Chrysler (FCA US LLC) is recalling certain 2015-2017 RAM 1500, 2500, and 3500 pickup trucks equipped with a power locking tailgate and either a 5 foot, 7 inch or 6 foot, 4 inch bed. The tailgate actuator limiter tab may fracture and cause the tailgate to unlatch and open while driving.

  Risk and fix

  Risk: If the tailgate latch releases and the tailgate opens while driving, cargo may fall out, creating a road hazard and increasing the risk of a crash.

  Fix: Chrysler will notify owners, and dealers will repair the vehicle, free of charge. The recall began September 17, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U74.

• Electrical System:Wiring

  May 2018 · #18V332000

  Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.

  Risk and fix

  Risk: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.

  Fix: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.

• Equipment

  Dec 2017 · #17V824000

  Chrysler (FCA US LLC) is recalling various Dodge, Chrysler, and RAM vehicles equipped with Kidde Plastic-Handle or Push Button 'Pindicator' Fire Extinguishers. A list of the affected trailer models is available at: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17V824-0103.pdf. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf

  Risk and fix

  Risk: If the fire extinguisher does not function properly, it can increase the risk of injury in the event of a fire.

  Fix: Chrysler will notify owners instructing them to contact Kidde for a replacement fire extinguisher, free of charge. The recall began February 14, 2018. Owners may contact Chrysler customer service at 1-800-853-1403 or Kidde customer service service toll-free at 1-855-262-3540, or online at www.kidde.com and click on "Product Safety Recall" for more information. Chrysler's number for this recall is T82.

• Power Train:Automatic Transmission:Lever And Linkage:Column Shift

  Dec 2017 · #17V821000

  Chrysler (FCA US LLC) is recalling certain 2016-2017 Ram 3500 Cab Chassis with a Gross Vehicle Weight Rating (GVWR) of less than 10,000 lbs, 2011-2017 Ram 3500, 4500 and 5500 Cab Chassis vehicles, 2009-2017 Ram 1500 and 2010-2017 Ram 2500 and 3500 pickup trucks, all equipped with a column shifter. Pushing the brake pedal for prolonged periods when the vehicle is running and in PARK may cause the Brake Transmission Shift Interlock (BTSI) pin to stick in the open position. With the pin in the open position, the transmission can be shifted out of PARK into any gear without pushing the brake pedal or having the key in the ignition.

  Risk and fix

  Risk: Being able to shift the transmission without pushing the brake pedal and/or without a key in the ignition can increase the risk of an unintended vehicle rollaway that may result in personal injury or a crash.

  Fix: Chrysler will notify owners, and dealers will update the vehicle software, inspect the BTSI, and, as necessary, replace it, free of charge. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T79.

• Engine And Engine Cooling:Engine:Diesel

  Sep 2017 · #17V562000

  Chrysler (FCA US LLC) is recalling certain 2013-2017 RAM 2500, 3500, 3500 Cab Chassis, 4500 Cab Chassis, and 5500 Cab Chassis vehicles, equipped with Cummins 6.7L Turbo Diesel engines that have Concentric-brand water pumps without a vent hole. These water pumps may leak coolant.

  Risk and fix

  Risk: The leaking water pump can increase the risk of an engine compartment fire.

  Fix: Chrysler will notify owners, and dealers will replace the water pumps, free of charge. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T51.

• Wheels

  Aug 2017 · #17V499000

  Streetcar ORV LLC, dba American Expedition Vehicles (AEV) is recalling certain 2013-2017 RAM 2500 and 3500 heavy duty trucks, modified by AEV to be equipped with cast aluminum Katla 8.5" road wheels. The outer surface of the wheel may fracture, resulting in rapid air loss.

  Risk and fix

  Risk: If the wheel fractures, a loss of vehicle control can occur, increasing the risk of a crash.

  Fix: AEV will notify owners, and dealers will replace the wheels with wheels of similar value, free of charge. The recall began on August 30, 2017. Owners may contact AEV customer service at 1-248-926-0256 extension 500.

• Air Bags

  May 2017 · #17V302000

  Chrysler (FCA US LLC) is recalling certain model year 2013-2016 Ram 1500, Ram 2500, and 2014-2016 Ram 3500 vehicles. Certain driving conditions, such as driving off-road or debris striking the vehicle may cause the roll rate sensor to trigger a fault within the Occupant Restraint Controller (ORC). If this fault occurs, the rollover side curtain air bag and the seat belt pretensioner will be disabled from deploying.

  Risk and fix

  Risk: If the rollover side curtain air bags and seat belt pretensioners are disabled, there is an increased risk of injury to the vehicle occupants in the event of a crash that necessitates activation of these safety systems.

  Fix: Chrysler will notify owners, and dealers will update the ORC software, free of charge. The recall began June 26, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T25.

• Equipment

  May 2016 · #16E041000

  Chrysler (FCA US LLC) is recalling aftermarket Mopar Canvas Seat Covers for certain 2012-2016 RAM 1500, 2500, and 3500 trucks. These Mopar canvas seat covers were sold through Chrysler dealerships beginning October 15, 2015. The seat covers can impede the deployment of the seat thorax airbags.

  Risk and fix

  Risk: If the seat cover impedes the air bag deployment, the seat thorax air bags may not provide adequate protection in the event of a crash, increasing the risk of a injury.

  Fix: Chrysler will notify owners to remove the front seat covers and return them for a full refund. The recall began on July 1, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S30.

• Engine And Engine Cooling:Engine

  Sep 2015 · #15V592000

  Chrysler (FCA US LLC) is recalling certain model year 2016 Ram 2500, 3500, 3500 Cab Chassis and 4500/5500 Cab Chassis trucks manufactured July 31, 2015, to August 13, 2015 and equipped with a 6.7L Cummins Diesel engine. In the affected vehicles, the Engine Control Module (ECM) may short circuit, causing the engine to stall without warning.

  Risk and fix

  Risk: An engine that stalls without warning increases the risk of a crash.

  Fix: Chrysler will notify owners, and dealers will replace the ECM, free of charge. The recall began on December 21, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R52.

Owner complaints by area

Reports owners filed with NHTSA. They aren't verified, and one complaint can mention more than one area. Tap an area to read the most recent ones.

• Power Train64

  7 involved a crash · 1 involved a fire

  • Filed Aug 2026

    I am reporting a transmission safety problem with my 2016 Ram 2500 Cummins that began shortly after FCA campaign U29 was performed. Before the recall work, the transmission and original solenoid were functioning normally. I had no transmission symptoms, warning lights, or transmission codes. The dealership performed U29 and replaced the transmission solenoid May 4-6, 2026. I picked the truck up May 6 at 149,091 miles. About 79 miles later, the check-engine light came on and transmission problems began. While driving, including on the interstate, the truck would suddenly jerk, the RPMs would rise quickly, and the truck would lose speed. On several occasions, traffic behind me had to react quickly to avoid hitting me. The dealership told me the solenoid installed during the U29 repair was defective and replaced it with another solenoid. The same problems continued. The truck later developed code P0871, became undriveable, and was towed back June 1. The original transmission ultimately failed. The dealership then installed a Mopar remanufactured transmission. I picked it up June 13. Within roughly 600 miles, it developed substantially identical symptoms and failure patterns, including P0870 and P0871, limp mode, and another major transmission failure. It was towed back June 24. The dealership later found the overdrive clutch had disintegrated and metal was present in the transmission fluid. The failed remanufactured transmission is now being handled under its Mopar warranty, and the dealership is looking to install a third transmission without identifying a clear reason for the repeated failures. I am concerned the same problem could happen again and believe the U29 repair, replacement parts, or another related transmission problem should be investigated.

  • Filed Aug 2026

    On August 25, 2026, my 2016 Ram 2500 was parked on private property. The driver states that she placed the automatic transmission in PARK before exiting the vehicle. After she exited, the unoccupied vehicle unexpectedly began rolling and struck a tree, causing vehicle damage. No one was injured. There were no known warning lights or messages indicating a problem before the incident. The cause has not yet been determined and the vehicle has not yet been inspected for this incident. The vehicle is available for inspection. This vehicle is equipped with a steering-column-mounted automatic transmission shifter. I am concerned that the incident may involve the transmission/shift interlock/Park system. I am aware of NHTSA Recall 17V-821 (FCA T79), involving unintended rollaway in certain Ram trucks, as well as NHTSA Recall Query RQ25003 concerning reported BTSI failures in vehicles including Ram 2500 models. The NHTSA VIN lookup currently shows zero unrepaired recalls for this vehicle; however, I do not yet know whether the prior T79 recall repair was performed on this specific vehicle or when it was performed. I did call the dealership and they said possibly 0ctober 3, 2018. I am submitting this complaint because the vehicle rolled after the driver reports placing the transmission in PARK and exiting the vehicle.

  • Filed Apr 2026

    Grid heater nut/bolt detached and entered engine, causing catastrophic internal failure and total engine loss while driving.

  • Filed Feb 2026

    Got into my truck after letting it warm up and the shifter broke out of the handle. It’s a known problem cause the design is flawed by putting so much pressure on the part. So in the end it breaks and then you can’t get your vehicle out of park or whatever gear it broke in. I was charged 718.00 for it to get fixed when I think this should be a recall or tsb.

  • Filed Nov 2025

    Incident Report – Gear Shift Failure Date of Incident: 11/10/2025 Vehicle: 2016 Ram 2500 Pickup Truck VIN [XXX] Mileage: [Insert Mileage] Location: [Insert Location of Incident] Description of Incident While attempting to shift the vehicle from Park (P) into Drive (D), the shift lever suddenly went limp and lost all resistance. Upon applying slight additional pressure to engage the transmission, the shift lever snapped off completely. The gear shift bracket—the component securing the shift rod—fractured in half at the point where the shift rod inserts into the bracket. This mechanical failure rendered the vehicle inoperable and unable to be shifted out of Park. No warning lights or prior symptoms were observed before the failure. The broken part was visually inspected and confirmed to be the shifting lever bracket, consistent with Mopar part number 68470756AA. Immediate Actions Taken The vehicle was safely secured to prevent unintended movement. Engine was turned off and keys removed. Visual inspection confirmed that the shift lever bracket had broken at the rod insertion point. Tow service was arranged for transport to a repair facility. Photographs of the damaged bracket and shifter assembly were taken for documentation. Assessment This incident represents a critical component failure of the gear shift mechanism, resulting in sudden loss of control over transmission operation. The break occurred under normal shifting force, indicating a possible material or design defect in the bracket assembly. Recommended Actions File a warranty or recall inquiry with Ram/Stellantis regarding potential defects in part 68470756AA. Replace the damaged bracket with a verified OEM replacement. Inspect surrounding linkage and cable components for stress damage or misalignment. Retain the failed part for potential recall or manufacturer investigation. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

  • Showing the 5 most recent of 64.
• Engine53

  1 involved a fire

  • Filed Apr 2026

    Grid heater nut/bolt detached and entered engine, causing catastrophic internal failure and total engine loss while driving.

  • Filed Feb 2026

    Adding to form 11717793

  • Filed Feb 2026

    The vgt actuator failed the truck only has 127000 miles on it ram extended the warranty for 2015 trucks but not 2016. The part to replace it from ram has almost doubled in a years time. It is now $2170. For this part whose internal computer components have failed. The files uploaded was just for the part. I can upload the repair cost when done. I am just trying to get everyone to see how corrupt these companies are becoming. They could have saved themselves some problems if they would just paid the $3000 to fix it this is a rough estimate.

  • Filed May 2025

    Towing my trailer with my 2016 Ram 2500, at 48,000 miles I experienced complete turbo failure in heavy traffic at highway speeds. Power was reduced to minimums causing hazardous conditions. The "check engine" light illuminated. I maintained control and eventually had the codes scanned at both a local auto parts store and Larry Miller Dodge/Ram in Sandy, Utah. The codes identified were for the turbo actuator/turbo. Larry Miller said they could replace the actuator, but I'd be back in three weeks for the turbo replacement as well. They were three weeks out for labor. I contacted a local diesel repair shop who purchased the turbo and actuator from Larry Miller Dodge Ram and had it installed in a day. Subsequent to these repairs ($5,400.00) I have learned that MOPAR issued Warranty Bulletin D-22-06, dated March 16, 2022, for the same make and model as mine, only for the year 2015. My truck was built in 2015 and the parts and computer codes for failure are identical. This published warranty bulletin issued relief of a new extended warranty of 15 years /150,000 miles for the installed turbo actuator/turbo. Since mine failed at 48,000 miles, this could be a continuation of the aforementioned issue with the stated 2015 year failures. I was lucky I didn't create a traffic accident when this turbo system failed since it was sudden and violent when the loss of power occurred without warning. I'm asking you to probe or look at the facts that the issue with these Garrett turbos are still outstanding whether Doge/Ram/Fiat/Mopar wants to include them in their campaign. The danger is real. The costs to retired people, such as myself, is consequential and devastating. It is unfair there is no way of sending queries to the manufacturers to alert them of this condition. The only way to communicate is to talk to a person in India and the communication barrier is tremendously difficult as is the chance of getting any return on the days and weeks of attempts for resolution.

  • Filed May 2025

    It is the Water pump We have the Concentric brand with out a vent hole picture attached ( which is the one under recall but doesn’t come up on our vin) Yes A Mechanic No No

  • Showing the 5 most recent of 53.
• Steering43

  • Filed Aug 2026

    the V06 Recall on this vehicle that for some reason was approved is an inadequate repair. The steering wheel is not adjustable with the "Weld Fix". Stellantis should have to replace the defective parts. My truck is not not able to be aligned 100%. The repair was done in 2019, and I have complained about this in the past once I realized what they did to "FIX" the issue for the recall. They have been no help and said that because it was and approved repair even though this should never of been a long term solution.. according to them I'm SOL and the dealership can align it but other shops are saying that you can't truly align the car and steering with that fix in place. I would hope that you put pressure on them to make this right.

  • Filed Jul 2026

    This complaint is against HENDRICK CHRYSLER DODGE JEEP RAM IN HOOVER ALABAMA misaligned solid-axle geometry and compromised tire casings triggered a violent, uncontrollable oscillation through the steering system, rendering the truck an immediate highway safety hazard. The vehicle was so dangerous to operate that it could not be driven home and remains stranded at a secondary residential location. IV. EXPEDITION OF COMPLAINT: DEALERSHIP BAD-FAITH REFUSAL Following the failure, a corporate case file was officially opened with Ram Corporate Customer Care. Upon notification of the corporate escalation, the owner/general management of Hendrick Chrysler Dodge Jeep Ram in Hoover, AL placed a direct phone call to the consumer. During this conversation, the dealership owner explicitly and aggressively stated that the dealership would do anything they had to do to get out of fixing the mistakes made on the drag link, directly refusing to authorize a safe flatbed tow, refusing to replace the ruined, improperly welded linkage, and refusing to assume liability for the three structurally destroyed tires. REQUESTED REMEDIAL ACTIONS The complainant requests that the National Highway Traffic Safety Administration (NHTSA), the Federal Trade Commission, and the Alabama Attorney General's Consumer Protection Division launch an immediate investigation into Hendrick Chrysler Dodge Jeep Ram for faulty execution of federal safety mandates, reckless endangerment of motorists, and bad-faith commercial practices. The dealership must be held legally and financially accountable for: The immediate cost of a flatbed tow from the vehicle's stranded location to a certified repair facility. The complete removal of the ruined, welded steering components and the installation of Ram’s updated, factory-authorized non-welded, clamp-style drag link assembly. The complete financial reimbursement or replacement of three (3) structural tires destroyed as a direct consequence of the failed recall execution.

  • Filed May 2026

    The contact owns a 2016 RAM 2500. The contact stated while driving at an undisclosed speed, the steering wheel failed to steer in the intended direction. In addition, the contact stated that the steering wheel independently steered the vehicle to the right. The vehicle was taken to the dealer, however the contact was informed that the alignment could not be completed because of an unrepaired recall repair. The contact received a recall notification, NHTSA Campaign Number: 19V021000 (Steering). The vehicle was taken to the dealer, however the contact was informed that the recall repair was completed in July 2019. The vehicle was not repaired. The manufacturer was made aware of the failure but provided no assistance. The contact was informed that the recall repair was covered under warranty for two years from the date of completion. The contact stated that the recall repair was not performed, but marked as completed by the dealer. The failure mileage was approximately 97,000.

  • Filed Jan 2026

    Drag link issue led to not being able to get an alignment, dealership and RAM support refused to fix it, as it was completed but they did not do it correctly the first time and it is dangerous

  • Filed Jan 2026

    The low pressure power steering hose is leaking and can't get part for it. Been having to invest in tons of power steering fluid and want to know if this is gonna be a recall. It is very frustrating that we can't get parts for the problem.

  • Showing the 5 most recent of 43.
• Electrical System38

  2 involved a crash · 1 involved a fire

  • Filed Aug 2026

    I am reporting a transmission safety problem with my 2016 Ram 2500 Cummins that began shortly after FCA campaign U29 was performed. Before the recall work, the transmission and original solenoid were functioning normally. I had no transmission symptoms, warning lights, or transmission codes. The dealership performed U29 and replaced the transmission solenoid May 4-6, 2026. I picked the truck up May 6 at 149,091 miles. About 79 miles later, the check-engine light came on and transmission problems began. While driving, including on the interstate, the truck would suddenly jerk, the RPMs would rise quickly, and the truck would lose speed. On several occasions, traffic behind me had to react quickly to avoid hitting me. The dealership told me the solenoid installed during the U29 repair was defective and replaced it with another solenoid. The same problems continued. The truck later developed code P0871, became undriveable, and was towed back June 1. The original transmission ultimately failed. The dealership then installed a Mopar remanufactured transmission. I picked it up June 13. Within roughly 600 miles, it developed substantially identical symptoms and failure patterns, including P0870 and P0871, limp mode, and another major transmission failure. It was towed back June 24. The dealership later found the overdrive clutch had disintegrated and metal was present in the transmission fluid. The failed remanufactured transmission is now being handled under its Mopar warranty, and the dealership is looking to install a third transmission without identifying a clear reason for the repeated failures. I am concerned the same problem could happen again and believe the U29 repair, replacement parts, or another related transmission problem should be investigated.

  • Filed Jul 2026

    To Whom It May Concern, I am requesting a no-cost replacement of the factory Uconnect 8.4 radio in my truck (VIN: [XXX]) due to daily safety-related failures that significantly affect the safe operation of my vehicle. Every day, the radio experiences a startup delay where the screen remains black and many center stack functions are unavailable. This delay often lasts 5–10 minutes before the system becomes operational. During normal driving, the radio also displays repeated “Vehicle Phone Requires Service” error messages, creating a constant distraction that takes my attention away from the road. When these issues occur, the factory backup camera is unavailable. Losing the backup camera eliminates an important safety feature intended to help prevent collisions with pedestrians, children, vehicles, and objects while reversing. Additionally, the factory navigation and GPS no longer function at all. These are not minor convenience issues—they are daily safety concerns. Safety-related features should work immediately every time the vehicle is started. A factory infotainment system that fails every day, disables the backup camera during startup, and repeatedly distracts the driver while the vehicle is in motion presents an unacceptable safety risk. Because these failures occur daily and involve factory-installed safety equipment, I believe Stellantis should replace the defective Uconnect radio at no cost. I respectfully request that this complaint be documented and that a no-cost replacement be authorized. Thank you for your prompt attention to this matter. [XXX] VIN: [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

  • Filed May 2026

    Electronic brake controller faulty

  • Filed Dec 2025

    ABS FAILURE, WHICH TURNS OFF TRACTION CONTROL AND CRUISE CONTROL. This is a known issue for the HCU to fail. How is this not a recall on 2016 but it is on 17 and 18. Same parts.... have replace front hubs with new ABS sensors and rear ABS sensors, still on. It has to be the HCU or the module.

  • Filed May 2024

    My ABS lights is on causing my cruise control to not be functioning. When I first start the vehicle, i get a message to "service electronic brake system." I have new brake pads with rotors and still have this message.

  • Showing the 5 most recent of 38.
• Service Brakes35

  1 involved a crash

  • Filed May 2026

    Electronic brake controller faulty

  • Filed Feb 2026

    ITBM Integrated Trailer Brake Module not outputting correct breaking voltage to trailer.

  • Filed Dec 2025

    ABS FAILURE, WHICH TURNS OFF TRACTION CONTROL AND CRUISE CONTROL. This is a known issue for the HCU to fail. How is this not a recall on 2016 but it is on 17 and 18. Same parts.... have replace front hubs with new ABS sensors and rear ABS sensors, still on. It has to be the HCU or the module.

  • Filed Apr 2025

    Def system failed ABS, track,tire pressure. Service 4 wheel drive system. 4 wheel drive system temporarily unavailable.

  • Filed Jul 2024

    Some time as i apply the brakes i get a pulse pushing back on the brake pedal , it results in a slower braking action . Also i have a power steering fluid leak coming from the brake booster system . The brakes and the power steering go through the same system . The brake problem has been happening about a year and the power steering leak at the booster about 2 months

  • Showing the 5 most recent of 35.
• Unknown or Other33

  1 involved a crash

  • Filed Feb 2026

    Got into my truck after letting it warm up and the shifter broke out of the handle. It’s a known problem cause the design is flawed by putting so much pressure on the part. So in the end it breaks and then you can’t get your vehicle out of park or whatever gear it broke in. I was charged 718.00 for it to get fixed when I think this should be a recall or tsb.

  • Filed Sep 2025

    The grab handle or left interior a arm part broke and fell of in my lap while I was driving luckily it did not fall off when I entered the vehicle or I would have been flat on my back. I contacted Stelantis got the typical run around. Tried to order new part but part has been discontinued. Now I am driving with airbag not covered and exposed. The part number for my truck is 5RM911XAC you can check discontinued. I ask Stelantis to find part after I tried for months to no avail. Reply was sorry part discontinued. What broke was the plastic that holds two screws in. Hopefully no one gets hurt if others break. In my opinion it seems like a bad design to save money. The replacement part by the way is $313.00 for plastic with leather wrapped handle. I was willing to spend that but the attitude I got from Stelantis was very non caring after I spent $60,000 on a truck in 2016. I ordered this part in May of 2025 then in August they told me it was discontinued.

  • Filed Jan 2024

    The tailgate will not stay closed. It comes open when driving and sometimes won’t stay closed at all. This is a common problem/recall with this model truck but for some reason doesn’t show up with my VIN #

  • Filed Jul 2023

    Driving truck and automatic changed to manual 4th gear - would not stay in automatic and would not go into any other manual gear at same time cruise stopped working along with the horn, seat belt light came on and would not go off , ESC light came on and did not go off, non of the steering wheel controls would work work , air bag light came in and would not go off , horn would not work at steering wheel but will when using key lock

  • Filed Feb 2023

    When vehicles comes to a stop or a slow roll. It makes a loud humming sound and cuts off in drive. The lights starts flickering ans The check engine flashes on at that time. Received a ecm code.I have to place in park and restart. Happens 70% of the time in drive and other times in reverse or park. Cruise control would not turn on. If on will not turn off with buttons

  • Showing the 5 most recent of 33.
• Vehicle Speed Control17

  1 involved a crash

  • Filed Dec 2025

    ABS FAILURE, WHICH TURNS OFF TRACTION CONTROL AND CRUISE CONTROL. This is a known issue for the HCU to fail. How is this not a recall on 2016 but it is on 17 and 18. Same parts.... have replace front hubs with new ABS sensors and rear ABS sensors, still on. It has to be the HCU or the module.

  • Filed Dec 2023

    ABS system/ Traction control system/ 4wheel drive system/ cruise control. I had the ABS system repaired/replaced once this year already and now i need it done again. ABS failure makes the 4wheel drive system fail and it's winter time and i need 4 wheel drive for safety.

  • Filed Jul 2023

    All brake warning lights came on , cruise control stopped working abruptly, service brake system warning dinger dinging , abs not working , engine braking all stopped working while loaded going steep grade , nearly lost control of the truck and was nearly in a serious accident , abs module and hcu said to be problem , issue still persists after said problem supposed to be resolved , truck is a death trap and there are multiple complaints about it , hcu and abs module are months back ordered , this needs recalled

  • Filed Feb 2022

    It seems that this is a common problem on these trucks the HCU for the antilock braking system and the ABS module has to be replaced the traction control light comes on the ABS light comes on and the cruise control does not work.

  • Filed Jan 2020

    I HAVE TRIED MANY TIMES TO GET THESE NUMEROUS SAFETY RECALL COMPLIED WITH AND GET NO FOLLOW UP FROM MY LOCAL DEALER! I TOOK IT IN FOR A SCHEDULED APPOINTMENT AND WAS TOLD PARTS WERE ON ORDER. IT'S BEEN FAR TO LONG, I HAVE CHECKED IN NUMEROUS TIMES AND GET NO HELP. PLEASE FIND A PLACE THAT CAN MAKE MY VEHICLE SAFE OR MAKE THEM BUY IT BACK FROM ME! I DON'T WANT TO DIE, OR KILL AN INNOCENT FAMILY! *DT*JB

  • Showing the 5 most recent of 17.
• Structure13

  1 involved a crash

  • Filed Jan 2024

    The tailgate will not stay closed. It comes open when driving and sometimes won’t stay closed at all. This is a common problem/recall with this model truck but for some reason doesn’t show up with my VIN #

  • Filed Dec 2021

    The tailgate still falls open unexpectedly while driving after the tailgate recall repair was done.. The tailgate fell open and hit my camper power jack and dented the tailgate above the handle.. I'd like the tailgate latch to be fixed correctly and the dent fixed as well.. im afraid to haul anything in the back that could potentially fall or slide out due to this issue..

  • Filed Jun 2019

    2016 DODGE RAM . CONSUMER WRITES IN REGARDS TO DRAG LINK SAFETY RECALL. *LD THE CONSUMER STATED THE WELDED BOLTS FOR THE DRAG LINK WOULD CAUSE AN ISSUE WITH HAVING AN ALIGNMENT PERFORMED ON THE VEHICLE. *JS

  • Filed Apr 2019

    HAVE 2016 RAM TRUCK, JUMPS OUT OF GEAR HITS A FENCE. TAKE IT TO A DEALER THEY ADMIT THERE IS A RECALL. THEY REPAIR THE RECALL AND TELL ME TO CALL FCA CUSTOMER SUPPORT 1800-992-1997 I SPEAK WITH QUINTIN AND HE TELLS ME SINCE THE DEALER ALREADY REPLACED THE PART, THEY CAN NOT CONFIRM THAT IS WHY MY TRUCK ROLLED INTO A FENCE. AND DENIED THE BODY REPAIRS. I ASK FOR DOCUMENTATION THAT STATES WHY THEY ARE REFUSING TO REPAIR DAMAGE DUE TO THEIR DEFECTIVE PRODUCT. THEY TELL ME THAT IS CONFIDENTIAL AND THAT I NEED TO GO THRU MY INSURANCE TO MAKE A CLAIM. SO I HAVE TO PAY FOR THEIR FAULTY EQUIPMENT. LESSON LEARNED DON'T PURCHASE FROM CHRYSLER ...

  • Filed Feb 2019

    TL* THE CONTACT OWNS A 2016 RAM 2500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 18V486000 (STRUCTURE, LATCHES/LOCKS/LINKAGES). THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. RAIRDON'S CHRYSLER DODGE JEEP RAM OF MONROE (16413 W MAIN ST, MONROE, WA 98272, (360) 805-5500) WAS CONTACTED AND CONFIRMED THAT THE PARTS WERE NOT AVAILABLE FOR THE RECALL REMEDY. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. PARTS DISTRIBUTION DISCONNECT.

  • Showing the 5 most recent of 13.
• Suspension12

  1 involved a crash

  • Filed Jul 2026

    This complaint is against HENDRICK CHRYSLER DODGE JEEP RAM IN HOOVER ALABAMA misaligned solid-axle geometry and compromised tire casings triggered a violent, uncontrollable oscillation through the steering system, rendering the truck an immediate highway safety hazard. The vehicle was so dangerous to operate that it could not be driven home and remains stranded at a secondary residential location. IV. EXPEDITION OF COMPLAINT: DEALERSHIP BAD-FAITH REFUSAL Following the failure, a corporate case file was officially opened with Ram Corporate Customer Care. Upon notification of the corporate escalation, the owner/general management of Hendrick Chrysler Dodge Jeep Ram in Hoover, AL placed a direct phone call to the consumer. During this conversation, the dealership owner explicitly and aggressively stated that the dealership would do anything they had to do to get out of fixing the mistakes made on the drag link, directly refusing to authorize a safe flatbed tow, refusing to replace the ruined, improperly welded linkage, and refusing to assume liability for the three structurally destroyed tires. REQUESTED REMEDIAL ACTIONS The complainant requests that the National Highway Traffic Safety Administration (NHTSA), the Federal Trade Commission, and the Alabama Attorney General's Consumer Protection Division launch an immediate investigation into Hendrick Chrysler Dodge Jeep Ram for faulty execution of federal safety mandates, reckless endangerment of motorists, and bad-faith commercial practices. The dealership must be held legally and financially accountable for: The immediate cost of a flatbed tow from the vehicle's stranded location to a certified repair facility. The complete removal of the ruined, welded steering components and the installation of Ram’s updated, factory-authorized non-welded, clamp-style drag link assembly. The complete financial reimbursement or replacement of three (3) structural tires destroyed as a direct consequence of the failed recall execution.

  • Filed May 2025

    I received an NHTSA recall notice V06/NHTSA 19V-021 on or about April 2023, I brought this vehicle to Stat Line Jeep Dodge RAM located in Somerset, MA early April to fix the vehicle pursuant to the recall notice for a Drag Link problem/defect. Upon arrival the service department stated they had not received a welding machine necessary to fix the problem and to call for another appointment, On or about April 10, 2023, I again brought the vehicle to State Line RAM dealership to complete the repair. On May 31, 2023, I brought the vehicle to Town Fair Tire Center to have all 4 new tires replaced and have the front end aligned. I was told that the alignment could not take place since the dealership welded the "Tie Rods" together. I brought the vehicle back to State Line dealership and asked why my vehicle's tie rods were welded. They told me that the NHTSA had told them that was the fix. I wanted to know how to get the vehicle aligned and the dealership told me that I would have to pay $850.00 to replace them and that should have been done except the NHTSA said to weld them together.

  • Filed Jul 2023

    Right rear air bag twisted and got against the exhaust which caused the vehicles suspension to drop or not hold air. I was told it was the compressor leaking through and had compressor replaced. It is not the compressor and the vehicle right rear suspension continues to loose air. When the vehicle was looked at again the airbag was untwisted and had a burn mark from exhaust. This is definitely a safety issue concern! This has been ongoing since 2017 with no recall on this vehicle. I had it in the shop again for the same thing and was told this issue could not be resolved!

  • Filed Nov 2022

    In 2020, Dodge repaired a recall by welding the steering linkage nut to the drag link. This recall (V06) prohibits me to have the vehicle aligned by a tire repair/replacement shop. Additionally, the ability to align the vehicle relies on the dealer to break the weld, replace the nut and re-weld the part. This repetitive process in turn causes metal fatigue to the drive link, presenting another MAJOR safety concern. If the drive link were to fail, I would lose steering control and crash without warning. I have contacted Dodge directly and requested they replace the drive link on my vehicle to remedy this problem, however, they have refused. The cost to replace the drive link and re-align the vehicle (required after part replacement) is approximately $1,100. Much less money than would be paid out for a catastrophic fatality(ies) resulting from the failure of this part.

  • Filed Sep 2022

    My 2016 RAM has very loose steering and has almost caused me an accident several times due to my lack of control of the steering. The steering stabilizer jam nuts have been welded to the adjuster sleeve (as the referenced recalls below suggest as a fix) but the entire assembly rotates freely by hand! I am constantly having to get alignments to help control my steering, however, it seems to be getting worse and I am having to do alignments more often. Now, recall numbers 19V021000 and 18E096000 both refer to this problem for select RAM 2500s however, for some reason my VIN is not connected to this recall although it is obvious that it has been implemented on my truck. I bought my truck in 2018 used from a dealership. All the recalls that were indicated on my truck at the time were implemented, but so was the welding of the jam nuts even though my VIN doesn't reflect this recall action. I have an appointment with my Chrysler dealership this Thursday, but they told me that there probably wasn't much that they could do without the recall being attached to my VIN. This is currently my only vehicle and I am cautious and scared every time I drive it now since there is no warning as to when the steering loosens up and the truck seems to drive diagonally vice straight. I would greatly appreciate some help in this matter.

  • Showing the 5 most recent of 12.
• Fuel/Propulsion System12

  • Filed Apr 2025

    Def system failed ABS, track,tire pressure. Service 4 wheel drive system. 4 wheel drive system temporarily unavailable.

  • Filed Apr 2025

    The service engine lamp came on. When the mechanic investigated, it was determined that the problem is identical to the Warranty Bulletin titled Cummins 6.7L Turbocharger Actuator - X99 Warranty Extension that pertains to the 2015 RAM 2500 pickup. My vehicle is a 2016 and there is no warranty extension, even though it is an identical problem. The vehicle was not drivable as is and I had to replace the Turbocharger Actuator. I am assuming that this is a known problem to Cummins and to RAM. There should be a Warranty Bulletin for the 2016 also.

  • Filed Oct 2022

    The contact owns a 2016 Ram 2500. The contact stated while driving at 65 MPH, the contact smelled a strong odor of gasoline and the contact felt the vehicle losing power. In addition, the contact noticed smoke coming from the rear of the vehicle, and no warning lights illuminated on the instrument panel. The contact placed a rubber line on the fuel line because he noticed the fuel line was rubbing against the frame of the vehicle causing the fuel line to wear. The vehicle was not diagnosed. The manufacturer was contacted, and a case was filed. The failure mileage was 87,000.

  • Filed May 2019

    MY VEHICLE HAS WAS HAS BEEN COINED AS "DEAD PEDAL" THE TRUCK WILL HESITATE FOR A SECOND WHILE ACCELERATING. THIS PROBLEM HAS BEEN WELL DOCUMENTED BY MANY OTHER RAM DIESEL TRUCK OWNERS. THIS WILL HAPPEN WHEN MERGING INTO TRAFFIC OR CROSSING A STREET AND CAN BE VERY DANGEROUS.

  • Filed Feb 2019

    THE HARDWARE SECURING THE EXHAUST MANIFOLD TO THE ENGINE HEADER BREAK AND CAUSE AN EXHAUST LEAK. EXHAUST CAN BE SMELLED IN THE CAB WHEN RUNNING THE HEATER.

  • Showing the 5 most recent of 12.
• Air Bags11

  5 involved a crash · 1 involved a fire

  • Filed Jan 2025

    Contacted FCA Recall Assistant Center on 10/23/2024 and filed a complaint against Corwin Chrysler Dodge, 3306 E. Kearney St., Springfield, MO., 65803 regarding Safety Recalls that Corwin Chrysler Dodge fraudulently checked off in the system as fixed, but they were not fixed. Case# [XXX] was assigned to the complaint. Keith is the assigned CS Manager and can be reached at 844-378-0575, ext: 3124. Keith informed us today that his hands are tied at this time and he doesn't have the authority to uncheck the safety recalls in the system that would be up to the dealership Corwin Chrysler Dodge in Springfield, MO. As of today, January 15, 2025, we still do not have resolution to this issue. We were informed to reach out to James River Dodge RAM, Ozark, Missouri. List of recalls below that we are aware that were completed by Corwin Chrysler Dodge of Springfield, Missouri. 1. Water Pump Recall T51 (Corwin Chrysler Dodge completed) 2. New Tailgate Latch U74 (Corwin Chrysler Dodge completed) We spoke to David, Service Manager, on 10/25/2024 and was informed since the system shows everything regarding the safety recalls for this vehicle are checked off in the system as fixed by Corwin Chrysler as completed. David told us that the safety recalls in the system that are showing fixed would need to be unchecked in the system in order for his team to recheck all the recalls on this vehicle and get paid for the service, because Corwin was paid for fixing the safety recalls when they checked them off in the system. 1. Steering - Drag Linkage Welded V06 (James River Chrysler could visibly see this was completed (10/25/2024) 2. Truck Engine Recalibration 67A (James River Chrysler completed on 10/25/2024) No other recalls to the best of our knowledge have been fixed on our 2016 RAM, Dodge Laramie 2500, 6.7L, Diesel Motor, vehicle. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

  • Filed Jul 2023

    Right rear air bag twisted and got against the exhaust which caused the vehicles suspension to drop or not hold air. I was told it was the compressor leaking through and had compressor replaced. It is not the compressor and the vehicle right rear suspension continues to loose air. When the vehicle was looked at again the airbag was untwisted and had a burn mark from exhaust. This is definitely a safety issue concern! This has been ongoing since 2017 with no recall on this vehicle. I had it in the shop again for the same thing and was told this issue could not be resolved!

  • Filed Jul 2023

    Driving truck and automatic changed to manual 4th gear - would not stay in automatic and would not go into any other manual gear at same time cruise stopped working along with the horn, seat belt light came on and would not go off , ESC light came on and did not go off, non of the steering wheel controls would work work , air bag light came in and would not go off , horn would not work at steering wheel but will when using key lock

  • Filed Mar 2022

    I was involved in a single vehicle accident due to a medical issue. I hit a utility pole, took out a cyclone fence, proceeded across a front yard of a home then almost directly into a block retaining wall. I was wearing my seat belt. My airbags did not deploy but I have no idea how fast I was going. From the damage to the pole and the wall and my truck I had to be going a decent speed. The police report noted that when they arrived my foot was on the accelerator and the back wheels were spinning for what that’s worth.

  • Filed Feb 2022

    There has been an open recall on this vehicle since August 2021. It was reported to be by the dealership this is at that this was due to have a remedy to fix the SABIC in the 4th Quarter of 2021. IT has yet to have a remedy pushed out. I was also told that the Y55 recall is grouped together with the Y63 Recall. I agreed with the dealership in October of 2021 that I would purchase this vehicle, and they told me the recall remedy would be out the following month. I have been patiently waiting with no resolution from RAM, MOPAR or Chrysler. I have contacted the dealership several times a week, and they keep telling my that MOPAR has been contact by them and they are not returning phone calls. This can not be sold until it is fixed, due to a Stop Sale Issued with the Recall Notice.

  • Showing the 5 most recent of 11.
• Engine And Engine Cooling7

  • Filed Feb 2026

    The contact owns a 2016 Ram 2500. The contact stated that while driving at various speeds, the check engine warning light illuminated, and the vehicle lost motive power and went into LIMP Mode. The contact stated that the failure was intermittent but also occurred while towing a 30-foot trailer or a 24-foot trailer. Occasionally, after pulling over, turning off, and restarting the vehicle, the vehicle returned to normal functionality. On other occasions, the vehicle was towed back to the residence after the failure. The vehicle was taken to an Auto Parts Store and diagnosed using a handheld scanner, and a fault code associated with the turbo actuator for the diesel engine was retrieved. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The contact called a local dealer and was notified of Technical Service Bulletin Number: 09-005-22; however, the vehicle was not included. The manufacturer was informed of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 113,000.

  • Filed Oct 2021

    Engine Fan / Radiator Shroud. During hot weather and engine temperature, the engine fan engaged. Due to the high ambient, I believe the radiator shroud was hot and the material was soft, it became deformed under the vacuum created by the fan cause it to interfere with the engine fans path of rotation. The interference caused the fan and shroud to shred each other sending shrapnel in all directions, including into the back side of the radiator, engine compartment. Plastic debris was found on top of the valve cover, battery, radiator, exhaust manifold. This problem has been reported by numerus online forms. This failure was inspected by the dealer and I was informed it was not under warranty, but drivable and safe. Their recommendation however was to replace the fan, shroud and radiator. However, they have seen cases with far worse damage causing catastrophic failure of the radiator leaving the vehicle stranded

  • Filed Jun 2020

    TL* THE CONTACT OWNS A 2016 RAM 2500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V818000 (EQUIPMENT, ENGINE AND ENGINE COOLING) AND 20V036000 (POWER TRAIN) HOWEVER THE PARTS TO DO THE REPAIRS WERE NOT AVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIRS. THE CONTACT STATED THAT THE VEHICLE WAS TAKEN THREE TIMES TO LANDMARK DODGE CHRYSLER JEEP RAM, 6850 MT ZION BLVD, MORROW, GA 30260, AND WAS REJECTED TO BE SERVICED DUE TO THE PARTS NOT BEING AVAILABLE. THE MANUFACTURER WAS NOT MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE FOR NHTSA CAMPAIGN NUMBER: 19V818000 (EQUIPMENT, ENGINE AND ENGINE COOLING), AND PART DISTRIBUTION DISCONNECTED FOR NHTSA CAMPAIGN NUMBER: 20V036000 (POWER TRAIN).

  • Filed Sep 2018

    TL* THE CONTACT OWNS A 2016 RAM 2500. THE CONTACT STATED THAT NHTSA CAMPAIGN NUMBER: 17V5612000 (ENGINE AND ENGINE COOLING) EXCEEDED A REASONABLE AMOUNT OF TIME FOR REPAIR. THE CONTACT RECEIVED THE RECALL NOTIFICATION IN SEPTEMBER OF 2017. THE DEALER (RALPH SELLERS CHRYSLER DODGE JEEP RAM, 14215 AIRLINE HWY, GONZALES, LA 70737) STATED THAT THE PARTS WERE UNAVAILABLE FOR THE REPAIR. THE MANUFACTURER WAS NOT CONTACTED. THE CONTACT HAD NOT EXPERIENCED A FAILURE. PARTS DISTRIBUTION DISCONNECT. **TR THE CONSUMER STATED ALL REPAIRS COMPLETED ON 09/19/18. *TR

  • Filed Aug 2018

    TL* THE CONTACT OWNS A 2016 RAM 2500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 17V562000 (ENGINE AND ENGINE COOLING); HOWEVER, THE PARTS TO DO THE REPAIR WERE UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. MACCORD DODGE CHRYSLER JEEP (LOCATED AT 990 TENNANT WAY, LONGVIEW, WA) WAS CONTACTED AND CONFIRMED THAT THE PARTS WERE NOT AVAILABLE FOR THE RECALL REMEDY. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE AND WAS NOT ABLE TO CONFIRM WHEN THE PARTS WERE TO BECOME AVAILABLE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. PARTS DISTRIBUTION DISCONNECT. *TT *TR

  • Showing the 5 most recent of 7.
• Seat Belts6

  1 involved a crash · 1 involved a fire

  • Filed Jan 2025

    Contacted FCA Recall Assistant Center on 10/23/2024 and filed a complaint against Corwin Chrysler Dodge, 3306 E. Kearney St., Springfield, MO., 65803 regarding Safety Recalls that Corwin Chrysler Dodge fraudulently checked off in the system as fixed, but they were not fixed. Case# [XXX] was assigned to the complaint. Keith is the assigned CS Manager and can be reached at 844-378-0575, ext: 3124. Keith informed us today that his hands are tied at this time and he doesn't have the authority to uncheck the safety recalls in the system that would be up to the dealership Corwin Chrysler Dodge in Springfield, MO. As of today, January 15, 2025, we still do not have resolution to this issue. We were informed to reach out to James River Dodge RAM, Ozark, Missouri. List of recalls below that we are aware that were completed by Corwin Chrysler Dodge of Springfield, Missouri. 1. Water Pump Recall T51 (Corwin Chrysler Dodge completed) 2. New Tailgate Latch U74 (Corwin Chrysler Dodge completed) We spoke to David, Service Manager, on 10/25/2024 and was informed since the system shows everything regarding the safety recalls for this vehicle are checked off in the system as fixed by Corwin Chrysler as completed. David told us that the safety recalls in the system that are showing fixed would need to be unchecked in the system in order for his team to recheck all the recalls on this vehicle and get paid for the service, because Corwin was paid for fixing the safety recalls when they checked them off in the system. 1. Steering - Drag Linkage Welded V06 (James River Chrysler could visibly see this was completed (10/25/2024) 2. Truck Engine Recalibration 67A (James River Chrysler completed on 10/25/2024) No other recalls to the best of our knowledge have been fixed on our 2016 RAM, Dodge Laramie 2500, 6.7L, Diesel Motor, vehicle. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

  • Filed Aug 2023

    Hello! We have the driver seat and passenger seat that unlock after driving every mile. I have called the dealership and Chrysler and they say they cannot help me. This is a safety issue and I need assistance now

  • Filed Dec 2017

    WHEN PULLING A CAMPER THE TRUCK SHUT OFF (THERE WAS NO FUNCTION OF THE GAS OR BRAKE PEDAL) CAUSING THE CAMPER TO JACK KNIFE AND HIT THE REAR TAIL LIGHT. WHEN THE CAMERA CAUGHT UP TO THE TRUCK WET SPUN 180 DEGREES AT 65 MPH THEN FLIPPED. NO AIRBAG WENT OFF AND THE SEATBELT DID NOT STAY LOCKED. MY SON WHO WAS SITTING IN THE BACK CLIMBED OUT OF THE BACKSEAT WITHOUT UNLATCHING HIS SEATBELT.

  • Filed Oct 2017

    DRIVER'S SEAT BELT BUCKLE RELEASES THE SEAT BELT WITHOUT BEING TOUCHED. I TUG ON THE BELT EVERY TIME I LATCH IT BECAUSE OF THIS BUT IT STILL RELEASES THE BELT AFTERWARDS ABOUT 30% OF THE TIME, USUALLY JUST AFTER PULLING AWAY FROM THE PARKING SPOT. I BOUGHT THE TRUCK WITH 48, 000 MILES ON IT AND ALMOST 1 YEAR OLD. IT HAS DONE THIS SINCE I FIRST BOUGHT IT.

  • Filed Sep 2016

    TL* THE CONTACT OWNS A 2016 RAM 2500. SHORTLY AFTER PURCHASING THE VEHICLE, THE REAR WINDOWS FAILED TO OPERATE. THE VEHICLE WAS TAKEN TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE REAR WINDOW MOTOR FAILED AND NEEDED TO BE REPLACED. THE VEHICLE WAS REPAIRED. AFTER THE REPAIR, THE CONTACT ATTEMPTED TO SECURE A CHILD SAFETY SEAT IN THE REAR OF THE VEHICLE; HOWEVER, THE SEAT BELT CAME OUT OF THE SEAT BELT HOUSING. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. AFTER SPEAKING WITH THE MANUFACTURER, THE CONTACT WAS INFORMED THAT A TEAM FROM THE MANUFACTURER WOULD HAVE TO INSPECT THE VEHICLE TO INSPECT THE SEAT BELT FAILURE. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 400.

  • Showing the 5 most recent of 6.
• Tires6

  • Filed Sep 2024

    The contact owns a 2016 Ram 2500 equipped with Hankook Tires, Tire Line: Dynapro AT2, Tire Size: 275/70/R18, DOT Number: 1BJWBRNB. The contact stated that while his son was driving approximately 60-65 MPH, the vehicle started severely vibrating and shaking on the front passenger’s side of the vehicle. The driver pulled to the side of the road and removed and replaced the front passenger’s side tire with the spare. The vehicle was driven to Discount Tire where it was diagnosed that there was a bubble on the tire. The vehicle was taken to Walmart where the tire was replaced. The contact stated that approximately 3 months after replacing the tire, the driver’s side rear and driver’s side front experienced the same failure. The contact continued to drive at speeds lower than 20 -25 MPH. The dealer was not made aware of the failure. The manufacturer was not made aware of the failure. The vehicle failure mileage was 137,804, and the tire failure mileage was 23,000.

  • Filed Aug 2023

    The contact owns a 2016 Ram 2500 equipped with Landsail Tires, Tire Line: CLX-1, Tire Size: LT275/70/R18, DOT number: TBDEF75C. The contact stated while driving 50 MPH, the tread of the front passenger’s side tire separated, causing the vehicle to start shaking abnormally. The vehicle was taken to an independent mechanic where it was confirmed that the front passenger’s side tire tread had separated. The tire as not replaced. The tires were replacement tires. The dealer was not contacted. The manufacturer was not made aware of the failure. The vehicle failure mileage was approximately 42,000. The tire failure mileage was 34,449.

  • Filed Dec 2022

    Truck started shaking like a tire was out of round. Right front tire had separation (several large bubbles on the inside of the tire). I replaced that tire with a spare of a different brand. About 2 weeks later the left rear tire had the same issue. These tires are less than 1 year old and have less then 15,000 miles. I do not trust these tires any more and replaced them at significant cost.

  • Filed Aug 2019

    TL* THE CONTACT OWNS A 2016 RAM 2500 EQUIPPED WITH FALCON TIRES, TIRE LINE: UNKNOWN, TIRE SIZE: 275/70/R18 (NA). THE CONTACT STATED THAT THE INNER THREADS ON BOTH REAR TIRES WERE DEPLETED. THE VEHICLE WAS TAKEN BACK TO THE INDEPENDENT SHOP WHERE THE VEHICLE WAS PURCHASED. THE CONTACT WAS INFORMED THAT HE WOULD HAVE TO GO THROUGH THE MANUFACTURER. NO FURTHER ASSISTANCE WAS OFFERED. THE TIRES WERE NOT REPLACED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE VIN AND DOT NUMBER WERE NOT AVAILABLE. THE VEHICLE AND TIRE FAILURE MILEAGE WERE UNKNOWN.

  • Filed Oct 2016

    TL* THE CONTACT OWNS A 2016 RAM 2500 EQUIPPED WITH FIRESTONE TRANSFORCE HT TIRES, SIZE: LT275/70R18. THE CONTACT STATED THAT THE REAR TIRES HAD A REQUIRED PRESSURE OF 80 PSI, AND THE FRONT TIRES REQUIRED A PRESSURE OF 65 PSI. THE CONTACT STATED THAT THE REAR DRIVER AND PASSENGER SIDE TIRES EXCEEDED THE REQUIRED PSI, WHICH CAUSED THEM TO MOVE UP AND DOWN WHEN DRIVING. WHILE DRIVING APPROXIMATELY 63 MPH AND APPLYING THE BRAKE PEDAL, THE VEHICLE WAS UNSTABLE. THE VEHICLE WAS TAKEN TO THE DEALER, BUT WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE AND STATED THAT THE VEHICLE WAS FUNCTIONING AS DESIGNED. THE APPROXIMATE VEHICLE FAILURE MILEAGE WAS 12,600 AND THE TIRE FAILURE MILEAGE WAS UNKNOWN.

  • Showing the 5 most recent of 6.
• Wheels5

  • Filed Jan 2025

    Contacted FCA Recall Assistant Center on 10/23/2024 and filed a complaint against Corwin Chrysler Dodge, 3306 E. Kearney St., Springfield, MO., 65803 regarding Safety Recalls that Corwin Chrysler Dodge fraudulently checked off in the system as fixed, but they were not fixed. Case# [XXX] was assigned to the complaint. Keith is the assigned CS Manager and can be reached at 844-378-0575, ext: 3124. Keith informed us today that his hands are tied at this time and he doesn't have the authority to uncheck the safety recalls in the system that would be up to the dealership Corwin Chrysler Dodge in Springfield, MO. As of today, January 15, 2025, we still do not have resolution to this issue. We were informed to reach out to James River Dodge RAM, Ozark, Missouri. List of recalls below that we are aware that were completed by Corwin Chrysler Dodge of Springfield, Missouri. 1. Water Pump Recall T51 (Corwin Chrysler Dodge completed) 2. New Tailgate Latch U74 (Corwin Chrysler Dodge completed) We spoke to David, Service Manager, on 10/25/2024 and was informed since the system shows everything regarding the safety recalls for this vehicle are checked off in the system as fixed by Corwin Chrysler as completed. David told us that the safety recalls in the system that are showing fixed would need to be unchecked in the system in order for his team to recheck all the recalls on this vehicle and get paid for the service, because Corwin was paid for fixing the safety recalls when they checked them off in the system. 1. Steering - Drag Linkage Welded V06 (James River Chrysler could visibly see this was completed (10/25/2024) 2. Truck Engine Recalibration 67A (James River Chrysler completed on 10/25/2024) No other recalls to the best of our knowledge have been fixed on our 2016 RAM, Dodge Laramie 2500, 6.7L, Diesel Motor, vehicle. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

  • Filed Sep 2020

    THE VEHICLE WAS DRIVING ON THE HIGHWAY AT AROUND 60 MPH WHEN THE ABS AND TRACTION CONTROL WARNING LIGHTS CAME ON. IMMEDIATELY AFTER THE WARNING LIGHTS FLASHED ON, THE RIGHT FRONT BRAKE SEIZED UP FOLLOWED BY THE LEFT FRONT BRAKE. VEHICLE SKIDDED TO A HALT AND WAS NO LONGER DRIVE-ABLE DUE TO THE BRAKES BEING COMPLETELY SEIZED. THIS WAS EXTREMELY DANGEROUS AS THERE WAS NO WARNING OF THE SUDDEN STOP AND INABILITY TO FULLY CONTROL THE MOVEMENT OF THE VEHICLE. THE VEHICLE COULD ALSO NOT BE MOVED FURTHER FROM THE ROADSIDE. VEHICLE WAS TOWED TO A DEALERSHIP. THE DEALERSHIP REPORTED THAT THE BRAKE CALIPER BRACKET BROKE CAUSING THE FRONT HUB BEARING TO BLOW APART WHICH LED TO DAMAGE OF THE BRAKE PADS AND ROTORS. THE LEFT FRONT ROTORS WERE DAMAGED FROM THE HEAT OF LOCKING UP.

  • Filed Feb 2020

    TL* THE CONTACT OWNS A 2016 DODGE RAM 2500. WHEEL STUDS SHEARED WHILE DRIVING. VEHICLE WAS UNSAFE TO OPERATE POSSIBLE CRASH DUE TO LOSS OF WHEEL STUD SUPPORT THE CONTACT STATED THAT WHILE DRIVING AT 65 MPH, THERE WAS AN ABNORMALLY LOUD SOUND COMING FROM THE FRONT OF THE VEHICLE. THE CONTACT WHO WORK AS A MECHANIC PERFORMED A SELF EVALUATION OF THE VEHICLE AND BECAME AWARE THAT FIVE OF THE WHEEL STUDS ON THE DRIVER'S SIDE FRONT WHEEL HAD SHEARED OFF. THE CONTACT STATED THAT THE WHEEL BEARINGS WERE PREVIOUSLY REPLACED BY BURDICK DODGE CHRYSLER JEEP RAM 5885 CIR DR E #335, CICERO, NY 13039 (315) 699-3846. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 90,000.

  • Filed Jul 2017

    PURCHASED 2016 DODGE RAM 2500 LARAMIE, MEGA CAB - NOTICEABLE VIBRATION AT HIGHWAY SPEEDS BETWEEN 60-80MPH - AT CERTAIN SPEEDS IT'S CONSTANT, AT OTHER SPEEDS IT'S INTERMITTENT. NOTIFIED DEALERSHIP WHO SUGGESTED BALANCING TIRES, ROAD FORCING TIRES, ETC BEFORE BRINGING IT IN FOR WARRANTY SERVICE. TOOK THE TRUCK TO SEVERAL TIRE SHOPS TO HAVE THE TIRES BALANCED, ROAD FORCED, CHANGED OUT FOR DIFFERENT TIRES, ETC. NOTHING RELATED TO TIRES "FIXED" THE ISSUE. BROUGHT TRUCK BACK TO DEALER FOR WARRANTY SERVICE, THEY REPLACED TWO TIRES THAT WERE (SUPPOSEDLY) "BAD" AND RETURNED THE TRUCK TO ME. ISSUE WAS NOT RESOLVED. RETURNED THE TRUCK FOR WARRANTY SERVICE AND REPORTED THE ISSUE TO FIAT CHRYSLER THE DEALERSHIP CHANGED OUT THE DRIVE SHAFT AND RETURNED THE VEHICLE TO ME INDICATING THAT THERE WAS NOTHING MORE THEY COULD DO AND THAT ANY REMAINING VIBRATION COULD NOT BE "FIXED." DROVE THE TRUCK HOME AND FELT THE VIBRATION. CONTINUED DRIVING AT HIGHWAY SPEEDS INCREASES THE VIBRATION. ONLY WAY TO "ELIMINATE" THE VIBRATION IS TO DRIVE AT 10 MILES BELOW OR ABOVE THE SPEED LIMIT ON THE INTERSTATE (NEITHER OF WHICH IS SAFE, IN MY OPINION).

  • Filed Jun 2017

    I'M HAVING PROBLEMS WITH TRYING TO FIND TIRES THAT A) RIDE WELL, AND B) LOOK GOOD TO ACCOMMODATE THE TIRE PRESSURE MONITORS. IN THIS TRUCK THE WARNING LIGHT IS SET SO HIGH THAT I HAVE TO KEEP 80 PSI IN THE TIRES. THE DEALER SAYS IT'S A REQUIREMENT BY THE NHTSA. ARE WE (CONSUMERS) STUCK WITH THIS PROBLEM, OR IS THERE SOME KIND OF "FIX" THAT WOULD ALLOW THE DEALER TO ADJUST THE WARNING DOWN TO SOMETHING LIKE 45 PSI? THANKS FOR YOUR TIME.

• Exterior Lighting5

  • Filed Jan 2020

    THIS IS THE TRADESMAN MODEL, WHICH IS THE BARE BONES BASIC WORK TRUCK. AT NIGHT, WHEN TURNING A 90 DEGREE CORNER, LEFT OR RIGHT, ONE CAN NOT SEE THE ROAD OR WHAT MIGHT BE COMING BECAUSE THE HEADLIGHTS DO NOT ILLUMINATE THE ROAD IN A SHARP TURN. IT IS ESPECIALLY WORRYING WHEN TURNING ON A DARK ROAD FROM A STOP SIGN. THIS HAS BEEN LIKE THIS SINCE THE TRUCK WAS NEW.

  • Filed Oct 2017

    TL* THE CONTACT OWNS A 2016 RAM 2500. THE CONTACT STATED THAT THE LOW BEAM HEADLIGHT WAS REPLACED THREE TIMES. THE VEHICLE WAS TAKEN TO THE DEALER (JACK WOLF CHRYSLER JEEP, 1615 N. STATE ST, BELVIDERE, ILL, 61108, 815-544-9211) WHERE IT WAS DIAGNOSED THAT THE BULBS BURNED OUT. THE TECHNICIAN REPLACED THE BULBS AND STATED THAT THE FAILURE WAS A KNOWN ISSUE. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE AND OFFERED TO REIMBURSE THE CONTACT FOR THE REPLACEMENT BULBS. THE CONTACT STATED THAT HE DID NOT RECEIVE A NOTIFICATION FOR AN UNKNOWN RECALL RELATED TO THE ELECTRICAL SYSTEM AND EXTERIOR LIGHTING. THE FAILURE MILEAGE WAS APPROXIMATELY 18,000. PARTS DISTRIBUTION DISCONNECT.

  • Filed May 2016

    MY 2016 RAM 1500 ALMOST KILLED ME THIS MORNING. TRUCK HAS 4,000 MILES ON IT. AT 4 AM I WAS DRIVING ON I-10 EAST BOUND 170 MILES FROM PENSACOLA. CRUISE WAS SET AT 78 AND I WAS IN THE PASSING LANE. THE ROAD WAS PITCH BLACK. WITHOUT ANY WARNING THE ENGINE LOST POWER AND ALL ELECTRICAL. HEADLIGHTS WENT DARK DASH BOARD, ETC. NEEDLESS TO SAY I WAS PANICKED AND MANAGED SOMEHOW TO MAKE IT TO THE RIGHT SHOULDER. AFTER GETTING TO THE SHOULDER EMERGENCY FLASHERS WOULD NOT WORK EVERYTHING WAS DEAD. JUST AS I WAS CONSIDERING GETTING OUT OF THE VEHICLE POWER CAME BACK ON. I PUT ON FLASHERS AND AFTER I CALMED DOWN RETURNED TO THE ROAD. THE NEXT 200 MILES WERE UNEVENTFUL. I WAS SCARED TO DRIVE AFTER DARK AFTER SUCH AN INCIDENT. I HAVE A APPOINTMENT IN FOLEY ALABAMA WITH DODGE NEXT MONDAY MORNING. ALSO BACK IN MARCH I WAS WAITING ON THE LEFT TURN LANE AND THE TRANSMISSION SHIFTED FROM DRIVE TO PARK ALL BY ITS SELF.

  • Filed Mar 2016

    NO DAYTIME RUNNING LIGHTS

  • Filed Oct 2015

    LIFE AND DEATH SITUATION: THE 2016 2500 RAM DIESEL TRUCK HAS A PROBLEM THAT CAUSES IT TO DO A COMPLETE ELECTRICAL SHUTDOWN WHILE DRIVING. A COMPLETE LOSS OF ALL ELECTRICAL SYSTEMS ARE LOST, INCLUDING A... COMPLETE ENGINE FAILURE... BRAKE LIGHTS... POWER STEERING... POWER BRAKES. EVERYTHING DIES WITH NO WARNING. JUST DEAD! FIAT DODGE RAM KNOWS ABOUT THIS PROBLEM AND ARE ALLOWING THESE VEHICLES TO BE SOLD TO AN UNKNOWING PUBLIC. THE REASON I KNOW THIS IS BECAUSE WHEN THE DEALER CALLED THE STAR HOT LINE AT RAM THEY WERE TOLD EXACTLY WHERE TO GO TO FIND THE PROBLEM!!! THERE HAVE BEEN NUMEROUS FAILURES TO DATE. THIS WILL GET PEOPLE KILLED. THE 2016 RAMS HAVE ONLY BEEN ON THE ROAD FOR A MONTH. I OWN ONE AND MY VEHICLE IS PRESENTLY IN THE SHOP FOR REPAIR AFTER 10 ENGINE FAILURES!!!! WHEN THERE WERE NO FAILURE CODES ON MY RAM 2500.. AND.. IT FAILED AND SHUT DOWN ON THE TECH WHEN BACKING IT OUT OF THE BAY THE VEHICLE WAS TAKEN AWAY FROM ME AS UNSAFE TO DRIVE. THAT WAS A WEEK AGO. IT IS STILL STUCK IN THE SAME BAY AS IT WILL NOT CRANK. PROBLEM: TIPM TOTALLY INTEGRATED POWER MODULE OR PDC INTEL PWR. PART # 68243265AD IS THE PROBLEM. THE MAIN TERMINAL INPUT CARRYING ALL ELECTRICAL POWER INTO THE VEHICLE IS BEING OVER TORQUED DURING MANUFACTURE. THIS IS CAUSING THE TERMINAL TO SNAP AND ONLY GIVE INTERMITTING POWER TO THE VEHICLE DURING OPERATION AND CAUSING THE TOTAL SHUT OF THE VEHICLE'S COMPUTERS AND SHUTDOWN OF THE VEHICLE. IN ADDITION TO THE THIS PROBLEM WHICH COULD CAUSE POSSIBLE DEATH, THE CONSTANT ARCING OF THE COMPUTERS HAS NOW CAUSED ADDITIONAL PROBLEMS TO MY VEHICLE. THERE IS NOW A FAILURE IN THE IGNITION SWITCH MODULE PART # 68271986AA AND IT HAS A ESD OF FEB 2016. I'LL DEAL WITH MY VEHICLE.. BUT ALLOWING THESE 8000# VEHICLES ON THE ROAD WITH THIS PROBLEM IS INEXCUSABLE WHEN DODGE RAM KNOWS THEY HAVE THIS SAFETY ISSUE. ....UPDATED 12/30/15 *BF UPDATED 05/21/18*JB

• Forward Collision Avoidance4

  • Filed Dec 2023

    ABS system/ Traction control system/ 4wheel drive system/ cruise control. I had the ABS system repaired/replaced once this year already and now i need it done again. ABS failure makes the 4wheel drive system fail and it's winter time and i need 4 wheel drive for safety.

  • Filed Jul 2023

    All brake warning lights came on , cruise control stopped working abruptly, service brake system warning dinger dinging , abs not working , engine braking all stopped working while loaded going steep grade , nearly lost control of the truck and was nearly in a serious accident , abs module and hcu said to be problem , issue still persists after said problem supposed to be resolved , truck is a death trap and there are multiple complaints about it , hcu and abs module are months back ordered , this needs recalled

  • Filed Feb 2023

    When vehicles comes to a stop or a slow roll. It makes a loud humming sound and cuts off in drive. The lights starts flickering ans The check engine flashes on at that time. Received a ecm code.I have to place in park and restart. Happens 70% of the time in drive and other times in reverse or park. Cruise control would not turn on. If on will not turn off with buttons

  • Filed Mar 2021

    ABS HCU COTROL MODULE IS OUT AND HAS BEEN OUT FOR YEARS TRUCK IS IN GOOD CONDITION NOW I HAVE NO TRACTION CONTROL OR CRUISE CONTROL

• Latches/Locks/Linkages3

  • Filed Feb 2019

    TL* THE CONTACT OWNS A 2016 RAM 2500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 18V486000 (STRUCTURE, LATCHES/LOCKS/LINKAGES). THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. RAIRDON'S CHRYSLER DODGE JEEP RAM OF MONROE (16413 W MAIN ST, MONROE, WA 98272, (360) 805-5500) WAS CONTACTED AND CONFIRMED THAT THE PARTS WERE NOT AVAILABLE FOR THE RECALL REMEDY. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. PARTS DISTRIBUTION DISCONNECT.

  • Filed Sep 2018

    TL* THE CONTACT OWNS A 2016 RAM 2500. WHILE DRIVING 55 MPH, THE TAILGATE UNLATCHED AND OPENED INDEPENDENTLY, WHICH CAUSED THE ITEMS ON THE BED OF THE VEHICLE TO FALL ONTO THE HIGHWAY. THE VEHICLE WAS TAKEN TO URSE DODGE CHRYSLER JEEP RAM (14 TYGART VALLEY MALL, WHITE HALL, WV 26554, (304) 363-9300), BUT THEY CLAIMED TO KNOW NOTHING ABOUT THE TAILGATE FAILURE. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT CONTACTED. THE FAILURE MILEAGE WAS 9,800. **TR *JB

  • Filed Aug 2018

    TL* THE CONTACT OWNS A 2016 RAM 2500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBERS: 17V821000 (POWER TRAIN) AND 18V486000 (STRUCTURE, LATCHES/LOCKS/LINKAGES). THE CONTACT CALLED GLENDENNING MOTOR COMPANY AT 641-464-3241 (LOCATED AT 1100 E SOUTH ST, MT AYR, IA 50854) AND WAS INFORMED THAT THE PARTS WERE NOT AVAILAABLE. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE AND WAS NOT ABLE TO CONFIRM WHEN THE PARTS WERE TO BECOME AVAILABLE. THE CONTACT STATED THAT HE RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 18V332000 (ELECTRICAL SYSTEM, VEHICLE SPEED CONTROL). THE VEHICLE WAS TAKEN TO THE SAME DEALER AND THE CRUISE CONTROL WAS REPROGRAMMED. WHILE DRIVING AT ANY SPEED, THE CRUISE CONTROL ACCELERATED OR DECELERATED RANDOMLY. THE VEHICLE WAS TAKEN BACK TO THE DEALER AND THE CRUISE CONTROL WAS REPROGRAMMED AGAIN. THE FAILURE RECURRED AND THE DEALER STATED THAT NOTHING ELSE COULD BE DONE. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE FAILURE MILEAGE WAS APPROXIMATELY 11,100. PARTS DISTRIBUTION DISCONNECT FOR 17V821000 (POWER TRAIN) AND VIN TOOL CONFIRMS PARTS NOT AVAILABLE FOR 18V486000 (STRUCTURE, LATCHES/LOCKS/LINKAGES).

• Equipment2

  1 involved a crash

  • Filed Jun 2020

    TL* THE CONTACT OWNS A 2016 RAM 2500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V818000 (EQUIPMENT, ENGINE AND ENGINE COOLING) AND 20V036000 (POWER TRAIN) HOWEVER THE PARTS TO DO THE REPAIRS WERE NOT AVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIRS. THE CONTACT STATED THAT THE VEHICLE WAS TAKEN THREE TIMES TO LANDMARK DODGE CHRYSLER JEEP RAM, 6850 MT ZION BLVD, MORROW, GA 30260, AND WAS REJECTED TO BE SERVICED DUE TO THE PARTS NOT BEING AVAILABLE. THE MANUFACTURER WAS NOT MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE FOR NHTSA CAMPAIGN NUMBER: 19V818000 (EQUIPMENT, ENGINE AND ENGINE COOLING), AND PART DISTRIBUTION DISCONNECTED FOR NHTSA CAMPAIGN NUMBER: 20V036000 (POWER TRAIN).

  • Filed Jan 2017

    2016 RAM DIESEL 6.7 L EXPERIENCING STALLING WHEN DECELERATING TO STOP - LOSE POWER, RAN OFF ROAD AS RESULT. VEHICLE HAS 3 SECOND DELAY WHEN ATTEMPTING TO ACCELERATE- SERIOUS SAFETY CONCERN CAUSED SEVERAL NEAR MISSES

• Hydraulic1

  • Filed Jun 2024

    The contact owns a 2016 Ram 2500. The contact stated that while driving at an undisclosed speed, the ABS warning light illuminated. The vehicle was taken to the dealer, who diagnosed a failure with the ABS control module. The vehicle was repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 22V140000 (Service Brakes, Hydraulic, Electronic Stability Control), but the VIN was not included. The manufacturer was not notified of the failure. The failure mileage was unknown. The VIN was not available.

• Electronic Stability Control (esc)1

  • Filed Jun 2024

    The contact owns a 2016 Ram 2500. The contact stated that while driving at an undisclosed speed, the ABS warning light illuminated. The vehicle was taken to the dealer, who diagnosed a failure with the ABS control module. The vehicle was repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 22V140000 (Service Brakes, Hydraulic, Electronic Stability Control), but the VIN was not included. The manufacturer was not notified of the failure. The failure mileage was unknown. The VIN was not available.

• Seats1

  • Filed Jan 2019

    REAR WINDOW LEAKING WATER ON ROOF, SEATS, AND CARPET. TRUCK WAS SITTING IN DRIVEWAY

• Trailer Hitches1

  • Filed Jun 2017

    TL* THE CONTACT OWNS A 2016 RAM 2500 EQUIPPED WITH A HENSLEY ARROW ANTI-SWAY TRAILER HITCH. WHILE DRIVING 5 MPH, THE VEHICLE MADE AN ABNORMAL NOISE. UPON INSPECTION, THE CONTACT NOTICED THAT THE A FRAME AND OFFSET RECEIVER BAR WERE FRACTURED IN HALF. A DEALER WAS NOT CONTACTED. THE MANUFACTURER WAS CONTACTED AND REQUESTED THAT THE PART BE SENT TO THEM AND ANY DAMAGES THAT OCCURRED WOULD HAVE TO GO THROUGH THE CONTACT'S INSURANCE COMPANY. THE VIN WAS UNKNOWN. THE FAILURE MILEAGE WAS APPROXIMATELY 500.

• Traction Control System1

  • Filed Sep 2016

    TL* THE CONTACT OWNS A 2016 RAM 2500. WHILE DRIVING APPROXIMATELY 53 MPH AND APPLYING THE BRAKES, THE VEHICLE LOST TRACTION ABILITY AND THE TPMS INDICATOR ILLUMINATED. THE VEHICLE WAS TAKEN TO A LOCAL DEALER AND THE TPMS WAS UPDATED. THE FAILURE RECURRED SEVERAL TIMES. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE AND STATED THAT NOTHING COULD BE DONE. THE FAILURE MILEAGE WAS APPROXIMATELY 12,000. ..UPDATED 12/20/16 *BF UPDATED 12/21/16.*JB

• Visibility/Wiper1

  • Filed Sep 2016

    TL* THE CONTACT OWNS A 2016 RAM 2500. SHORTLY AFTER PURCHASING THE VEHICLE, THE REAR WINDOWS FAILED TO OPERATE. THE VEHICLE WAS TAKEN TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE REAR WINDOW MOTOR FAILED AND NEEDED TO BE REPLACED. THE VEHICLE WAS REPAIRED. AFTER THE REPAIR, THE CONTACT ATTEMPTED TO SECURE A CHILD SAFETY SEAT IN THE REAR OF THE VEHICLE; HOWEVER, THE SEAT BELT CAME OUT OF THE SEAT BELT HOUSING. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. AFTER SPEAKING WITH THE MANUFACTURER, THE CONTACT WAS INFORMED THAT A TEAM FROM THE MANUFACTURER WOULD HAVE TO INSPECT THE VEHICLE TO INSPECT THE SEAT BELT FAILURE. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 400.

Safety ratings

NHTSA 5-Star Safety Ratings from government crash tests. Ratings can differ by cab style and 2WD/4WD.